This rug was a massive undertaking as it required adding new wool into the rug. The new fringes were done via implant work and were not sewn on. The rug has increased greatly in value and will be preserved for a long time.

This rug also required the appropriate fringe work that is a propos to the design and era of the rug.

Given the age and value of the rug, this is a rug that should not be sent to any rug store, but should go to Jafri Rug restoration as the weavers are specifically skilled to repair these threadbare rugs and understand the motifs and match the wool dye lot for dye lot. The artistry will maintain the antiquity of the rug and will not make it look newly made and will also raise the value of the rug.

Jafri Rug restoration will do the following:

1. Assessment and Inspection:

Condition Check: Inspect the rug thoroughly for signs of wear, including fraying edges, missing or damaged knots, stains, or fading. This is essential to assess the scope of restoration work needed.

Fabric Type: Identify the materials used (wool, silk, etc.) to ensure the correct restoration techniques and materials are used.

Color Matching: Persian rugs often feature vibrant and intricate color schemes. Color matching is important for any repairs to ensure the restoration blends seamlessly with the original.

2. Cleaning:

Gentle Cleaning: Before restoration, the rug is cleaned to remove dirt and stains. This is typically done by hand or machine using organic olive oil shampoo foam to cleanse the rug and techniques that preserve the integrity of the fibers.

Drying: After cleaning, the rug must be carefully dried to prevent any damage or shrinkage.

3. Repairing Damaged Areas:

Reweaving/Knots: If there are missing or damaged knots, the missing sections will be re-woven by hand. Skilled weavers use the same knotting technique that was used in the original rug to ensure consistency.

Fringe Repair: If the fringe is damaged or missing, it can be reattached or replaced using matching fibers.

Edge Repair: The rug’s edges may become frayed over time. A repair may involve re-binding the edges to prevent further unraveling.

4. Color Restoration:

If the rug has areas with faded or discolored sections, dyes matching the original colors may be applied to restore the vibrancy. This requires careful attention to detail to blend the colors seamlessly.           

Jafri Rug restoration will do the following:

The rug stretching & blocking process is a professional corrective procedure used to restore a handmade rug’s shape, dimensions, and structural alignment after it has become wavy, rippled, skewed, or curled. It is common with Persian, Oriental, and other hand-knotted rugs.

Jafri Oriental Rug Stretching & Blocking

1. Inspection & Measurement

• 
  

  Rug is measured corner-to-corner

  
  


• 
  

  Warp (length) and weft (width) tension is evaluated

  
  


• 
  

  Distortion patterns are identified

2. Controlled Moisture Introduction

• 
  

  Rug is lightly dampened with clean, temperature-controlled water

  
  


• 
  

  Never soaked at this stage

  
  


• 
  

  Moisture relaxes wool, cotton, or silk fibers

  
  

3. Alignment & Squaring

• 
  

  Rug is placed on a blocking table or frame

  
  


• 
  

  Pattern lines are used to visually realign the rug

  
  


• 
  

  Corners are squared and edges straightened

  
  

4. Gradual Tension Application

• 
  

  Tension is applied slowly and evenly

  
  


• 
  

  Stretched in the direction needed (warp, weft, or both)

  
  


• 
  

  Overstretching is avoided to prevent fiber fatigue

  
  

This step may take hours, not minutes.

5. Securing the Rug

• 
  

  Adjustable clamps to hold the rug together

  
  


• 
  

  Stainless steel pins

  
  


• 
  

  Blocking bars

  
  

Edges are secured without piercing pile or damaging foundation.

6. Flat Drying (Critical Step)

• 
  

  Rug dries completely flat

  
  


• 
  

  Controlled airflow and temperature

  
  


• 
  

  No heat, no hanging

  
  

Drying can take 24–72 hours, depending on rug thickness and humidity.

7. Final Inspection & Finishing

• 
  

  Measurements rechecked

  
  


• 
  

  Minor adjustments if needed

  
  


• 
  

  Edges and corners reinforced if necessary